CYBEX U.GO Manuel du propriétaire Page 29
- Page / 100
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Assembly and Set Up
Page 2-13
Cybex Arc Trainer 750A/750AT Owner’s Manual
Right
Handle
Assembly
Figure 12 (750AT)
Correct Position
Left
Handle
Assembly
Using a 3/16” Allen wrench (#7), secure linkage rod to handle assembly with G. linkage rod cap 2.00
OD (#20), flange spacer (#17), SHCS .250-20 UNC-3A SS (#19) and fl at washer, .281 ID x .500
OD x .062 T (#18) as shown in Figure 11. NOTE: The SHCS .250-20 UNC-3A SS (#19) must be
tightened to a minimum of 90 in/lbs.
16. Install right handle assembly.
Position the right handle assembly in the correct position on the right side where the left handle A.
assembly was removed in step 14E. See Figures 10 and 11.
Figure 13 (750AT)
Heart Rate
Wire
Main Frame
Socket
NOTE: Position plug so
handle does not
rub cable during
operation.
Apply loctite (#16)B. to threads inside the arm and
screws removed in step
14B. See Figure 11.
Place right handle assembly in position and slide C.
pivot pin back in place. See Figure 10.
Secure handle assembly with the screws and D.
washers removed in step 14B. See Figure 10.
Locate right linkage rod, right handle assembly, E.
linkage rod cap 2.00 OD (#20), flange spacer
(#17), SHCS .250-20 UNC-3A SS (#19), and flat
washer .281 ID x .500 OD x .062 T (#18). See
Figure 11.
Place a drop of threadlocker (#21) on each F.
SHCS .250-20 UNC-3A SS (#19) and another
drop inside the shaft into which the SHCS will be
tightened.
Secure linkage rod to handle G.
assembly with linkage rod cap
2.00 OD (#20), flange spacer
(#17), SHCS .250-20 UNC-3A
SS (#19) and flat washer .281
ID x .500 OD x .062 T (#18)
as shown in Figure11. NOTE:
The SHCS .250-20 UNC-3A
SS (#19) must be tightened to
a minimum of 90 in/lbs.
Verify handle assemblies are H.
now installed in the correct
position as shown in
Figure 12.
- Cybex Arc Trainer 1
- 750A/750AT 1
- Owner’s Manual 1
- Cardiovascular Systems 1
- Table of Contents 5
- About This Manual 7
- FCC Compliance Information 7
- 1 – Safety 9
- Page 1-2 10
- Important Safety Instructions 10
- User Safety Precautions 10
- Page 1-3 11
- Facility Safety Precautions 11
- DISCONNECT POWER 12
- BEFORE SERVICING 12
- Voltage: 100-240 VAC~ 12
- 50/60Hz 1.8 Amps 1-Phase 12
- Moving parts 13
- Keep hands away 13
- Page 1-6 14
- CSAFE Port (J9) 15
- Communication 15
- 8V DC/100 MA 15
- Power Supply 15
- Back of Console 15
- Page 1-8 16
- 2 – Assembly and Set Up 17
- 750A Contents 18
- 750A Hardware Pack 20
- 750AT Contents 21
- 750 AT Hardware Pack 22
- Testing Operation 31
- Setup Screen 32
- Assembly and Set Up 34
- Page 2-18 34
- 3 - Operation 35
- Mount and Dismount 36
- Emergency Dismount 36
- Console Keys 38
- HEADPHONE PORT 40
- Navigation 41
- Program Selection 41
- Programs P1 – P9 Setup 42
- A1 – Constant Power Setup 43
- A2 – Power Training Setup 43
- Custom Programs 43
- To save custom program 43
- To play back custom program 44
- To delete a custom program 44
- Data Readouts 44
- – 69 BPM 45
- – 93 BPM 45
- – 119 BPM (Fat Burn Zone) 45
- – 169 (Cardio Zone) 45
- Alarm Set 46
- Battery Sentry 46
- 4 - Preventive Maintenance 47
- Maintenance 50
- Page 4-4 50
- Every 5000 Miles (8000 KM) 50
- Every 20,000 Miles (32000 KM) 50
- Statistics 50
- 5 - Customer Service 53
- Ordering Parts 54
- Damaged Parts 55
- 750A Technical Specifications 57
- Technical Specifications 58
- Weight Loss 59
- Figure 1 60
- P2 Hills 61
- Figure 2 62
- Hill Interval 63
- Program Overviews 64
- Page B-6 64
- Pikes Peak 65
- Page B-8 66
- Interval 1:1 67
- Page B-10 68
- Interval 1:2 69
- Page B-12 70
- Strength 71
- Figure 7 72
- P8 Cardio 73
- Figure 8 74
- Parts List 75
- Page C–1 75
- Page C–2 76
- Exploded Views 77
- Page D–1 77
- 750A DRIVE FRAME ASSEMBLY 77
- Page D–2 78
- 750AT DRIVE FRAME ASSEMBLY 78
- Page D–5 81
- 750A LEFT SIDE ARM 81
- ASSEMBLY DETAIL 81
- Page D–6 82
- 750A RIGHT SIDE ARM 82
- Page D–7 83
- 750AT LEFT SIDE ARM 83
- 750AT RIGHT SIDE ARM 84
- Page D–8 84
- Page D–9 85
- 750A HANDLE 85
- ASSEMBLY 85
- Page D–10 86
- 750AT HANDLE 86
- Page D–11 87
- 750A/750AT FOOT PLATE 87
- Page D–12 88
- Page D–13 89
- Page D–14 90
- Page D–15 91
- Page D–16 92
- Page D–17 93
- Page D–18 94
- Page D–20 96
- DIGITAL PEM MONITOR OPTION 96
- Schematics 97
- Page E–1 97
Produits connexes et manuels pour Conditionnement physique, gymnastique et musculation CYBEX U.GO
Conditionnement physique, gymnastique et musculation CYBEX Eagle Calf Manuel du propriétaire
(54 pages)
(54 pages)
(74 pages)
Conditionnement physique, gymnastique et musculation CYBEX Eagle 11111 Manuel du propriétaire
(32 pages)
(32 pages)
Conditionnement physique, gymnastique et musculation CYBEX Bravo Lift Manuel d'utilisateur
(28 pages)
(28 pages)
Conditionnement physique, gymnastique et musculation CYBEX VR3 Prone Leg Curl Manuel d'utilisateur
(28 pages)
(28 pages)
Conditionnement physique, gymnastique et musculation CYBEX VR3 Back Extension Manuel d'utilisateur
(28 pages)
(28 pages)
© 2020, manymanuals.fr. Tous droits réservés | 0.743 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels